Safety Tips

Towing Service

Towing with a Flatbed Trailer

Flatbed trailers are used for moving a wide range of loads, especially vehicles. However, vehicles do roll about if they are not properly secured. Therefore, when precautions are not taking when moving items and loads with a flatbed trailer, mistakes will happen. You will need accessories and techniques to avoid any mishaps for smooth transportation. What is a Flatbed Trailer? Is it the Same as a Flatbed Tow Truck? ­Flatbed trailers are usually used to tow large, heavy commercial loads. They include lumber, machinery, large pipes, equipment, and so on. A type of flatbed trailer, which is called a low boy, has the flatbed sitting close to the ground level. They can tow large equipment and heavy tractors to and from construction or work sites. Flatbed tow truck consists of a ramp or platform, situated at the back of the tow truck. The platform looks like a bed, and thus the name of the tow truck. They also call the rollback trucks. They have hydraulic systems in place that enable moving the ramp or platform up and down, and the vehicle can be driven up onto the flatbed. Once the vehicle is placed, the hydraulics will balance the flatbed, and the truck can transport the loaded vehicle. Steps and Precautions to Take when Towing with Flatbed Trailers When you are towing heavy loads, the larger loads are top-heavy. And when towing is done using a flatbed trailer, extra precautions need to be taken. It is because vehicles have wheels, and wheels can make the vehicles roll off during transportation. Before hitting the road, one will need to fasten the loads to be transported. Accidents can happen unexpectedly, and people do make mistakes. When you are not careful handling these loads with a flatbed trailer, damages and loss will occur. Therefore, tying down the items or loads is essential. The following accessories are commonly used by tow truck drivers to tie-down the loads. Nylon strap They are used to reinforce the tie-down on the loads. Nylon straps come in different lengths and widths. V-Straps They are nylon straps that come with steel hooks at each end. V-straps can be used to latch onto parts below the undercarriage of a vehicle. Basket strap They are nylon straps with web-like design. Basket straps can fit over the wheels. They can also be attached or hooked to the eyelets of a trailer. Ratchets They are steel-ratchet mechanism combined with nylon straps to tighten and fasten the load. When the nylon straps are not available, one can consider using chains instead. The above-mentioned accessories also come in chain form. Next, we will discuss the proper loading procedure. When you have the appropriate towing equipment, and if you are towing an automobile, position the car on the trailer evenly and over the axel. Pull the car as far forward as possible without coming into contact with the front of the trailer. Set the parking brake, and put the automobile in gear should it has a standard transmission. With chock blocks, place one in front of the automobile, and one behind at least one wheel of the car. Tie Down the Loads Use the basket straps if available. Put one over each of the tires. It is necessary to ratchet the front tires as well as the rear tires. When the tires are secured, move below the automobile. This is when V-straps are used on the front and rear. Most of the automobiles have tie-down eyelets or tow hooks near the bumpers, be sure to utilize them. Do not hook the V-straps on any suspension components, because this may tear the parts of the automobile. Put the straps in opposite directions. In this way, one can tow the car from each way. Before moving off, ratchet and secure everything. Check the hitch, light, and safety chains as well. Drive with Care Drive with caution when traveling with a heavy load. Avoid fast maneuvers and drive at a safe speed. Be sure to give yourself enough space and time for emergency brakes, and to drive through the curves and turns smoothly. For 24-Hour Towing Services in Los Angeles, Please Call Green Towing Los Angeles

Towing Company

Tow Trucks and Towing Equipment Maintenance – Tips & Benefits

Tow trucks and towing equipment are essentials of a towing company. However, they do not last forever. Regular maintenance is necessary to keep the equipment in shape. If there are malfunctioning equipment or broken items, this may cause disruptions during towing works. In fact, it may even cause injuries to the towing staff or clients. Surely no towing business will want any of these issues to happen. So it takes a lot of preparation, routine check-ups, and maintenance to prevent any potential issues. The following are some tips for repairs and taking care of the towing equipment. Check the Tow Trucks to See if Anything is Wrong It is important to do routine examinations for the tow trucks. This can spot issues and prevent them from becoming bigger problems to the tow trucks. Due to long hours spent on the roads, tow trucks may experience breakage or failure in certain devices or equipment. Therefore, the tow truck drivers need to frequently check the tow trucks in case there are unseen mechanic failures and issues in the tow trucks. It will be very helpful if the towing drivers do regular walkarounds before and after any task. A Plan for Repairs Things will inevitably fail or break. Plan ahead; in the event when tow trucks need repairs, the business will be better prepared. Find out and research for the best possible solutions and repair service centers in the area. It is also important to note the servicing hours of the centers. Find out if they can accept requests for repairs during off-hours. By planning, the business will better handle any unexpected situations. Where to Receive the New Parts of the Equipment The chassis of any vehicle is important, especially for tow trucks. The management will need to plan and find out about the dealerships which can assist in getting the required vehicle parts. A relation or partnership with a distributor can be advantageous if when you require any original equipment manufacturer (OEM) parts. Although most of the towing vehicles have similar parts and components, there always exceptions. Therefore, relationships or partnerships with multiple distributors are necessary if the components are not available at certain distributors. The Appropriate Equipment in the Region The towing company may need certain tools in the respective region. For instance, they may need the right towing equipment in winter, and they may need specific equipment for certain towing jobs. Software for Keeping Track of the Maintenance Consider using a software to keep track of the preventive maintenance. The software can assist in preparing and preventing issues. They can also help in keeping track of maintenance costs, which is useful in planning the budget for the towing company. Software can also enable the company to be proactive in preventing issues, rather than reacting to them. Keep a Record of the Maintenance Keeping track of maintenance is a good idea for future references. record down the details of each maintenance, for instance, which equipment has worn out, how long it lasts, the reason for replacement, and when it was replaced. These details can help in identifying the components and parts, the availability of these parts, and get a replacement quickly without any delays. In this way, downtime is reduced. The towing company can also maximize the lifespan of the equipment by scheduling regular cleaning and replacing dates. The Benefits and Advantages in Regular Maintenance for Tow Trucks and Equipment Never underestimate the value of taking care of the towing equipment, as it can prevent any tailspin and disruptions for the business operations. Although it may take a lot of work in maintaining the towing equipment, there are numerous benefits and advantages in spending the time, effort, and money in maintenance. The towing business can prevent the downtime for the tow trucks, and this can prevent loss in income. In the long run, regular maintenance can keep the tow trucks working, and keep the business running at its optimal capacity. With both short-term and long-term benefits, it is wise to draw up a plan and work on the schedules for towing equipment maintenance. For 24-Hour Towing Services & Roadside Assistance in Los Angeles, Please Call Green Towing Los Angeles

Jump Start Car
Roadside Assistance

Jump Start a Car Safely Without Roadside Assistance

There will never be a convenient time to find out your car battery is dead. Depending on the brands, car batteries can last between 3 to 5 years. When your car battery is flat, what can get you back onto the road is a jump start. It gives the battery enough power to start the engine. Then, you can disconnect the power supply, and the engine will recharge the battery. Is Flat Battery the Source of the Problem? There are several reasons why the automobile will not start. One must check the battery before doing the jump start. Most car batteries come with code dates, informing the age of the battery. There are also other common signs to whether if the battery is dead or about to expire: – There is a clicking sound, but no engine turnover when the ignition key is turned on. – Before starting, the engine cranks slowly. – When the engine is not on, the headlights are dim. – Cracks or white substances can be seen on the car battery. Should the car battery looks damaged, it is advised not to jump it; inform a towing company to have the car towed to a mechanic for examination. How to do a Car Jump Start Yourself Make sure the electronics are switched off. They include both the exterior and interior lights, radio, air-con, and devices. They put a strain on the car battery, and additional power is needed at startup. Position the working car near to the stalled automobile. Put the emergency brakes on both vehicles and make sure they are both turned off. Your jumper cables should not be pulled tight, and can easily reach both car batteries. Switch off both automobiles and open the bonnet. Be sure to switch off all the electronics in the car that requires a jump start. Remove the key from ignition after checking the electronics are off. Connecting the Cables Identify the positive (+) and negative (-) terminals. Attach the positive clamp of the jump cable to the positive (+) terminal on the car with the flat battery. The positive cable is red in color, however, some cables may differ in the coloring. Then, attach the other end of the jump start cable to the positive (+) terminal on the live battery. Attach the black jump cable to a piece of unpainted and exposed metal on the car that needs a jump start. It needs to be away from the car battery as well. The purpose is to use it as a way to earth the power. After this, connect the other end of the jump cable to the negative (-) terminal of the working car. Start the engine of the working car, then leave it idle for about 5 minutes. When the 5 minutes is up, start the engine of the car with a dead battery. If it is completely drained of power, you might need a little touch of power while turning the ignition. And it doe not start straight away, do not turn the ignition for continuously longer than a few seconds, because it can flood the engine. If the battery is still dead, try to adjust the black cable again, so it has better contact with the bare metal. However, if it still does not work, then you could be facing a more serious issue. Removing the Jump Start Cables Remove the jump start cables in the reverse order from how they are attached to the batteries. The black cable from the unpainted metal surface should be removed first, next is the black cable from the negative terminal on the working battery, followed by the red jump start cable attached to the positive terminal on the working battery, and lastly, the red cable attached to the positive terminal on the flat battery. Safety Precautions When Doing a Car Jump Start As mentioned, check the condition of the batteries, and the jump cables. If there are signs of corrosion, rust, or damage, do not try a jump start. Forcing a jump start may damage the cars and even cause injury. Use a pair of rubber gloves when handling the jump start cables to minimize the risk of an electric shock. Remove any metal items, rings, or bracelets on yourself. The working car should be parked near the stalled car. When stranded on a highway or busy traffic, be cautious if you attempt a jump start. You can consider roadside assistance professionals to help you jump start the car safely. Examine the temperature of the jump cable plastic casing attached to both car batteries. When they become hot, remove the cables safely and call for professional roadside assistance instead. For 24-Hour Towing Services & Roadside Assistance in Los Angeles, Please Call Green Towing Los Angeles

Towing Service

Towing All-Wheel-Drive Vehicles Safely

All-wheel-drives are popular with car buyers due to their extra traction in various terrains and weather conditions. However, towing an all-wheel-drive can be a little more complicated compared to towing other vehicles. We will discuss the reasons and what you can do to tow the all-wheel-drive safely. What is an All-Wheel-Drive Before getting into details, first we will distinguish an all-wheel-drive (AWD) and a four-wheel-drive (4WD). An all-wheel-drive system. All-wheel-drives are optimized and geared for on-road usage. Their systems will use the front and rear differentials with an electronic or viscous coupling to split the power between each axle and individual wheels. Most all-wheel-drives are engaged permanently to different degrees, thus disengaging them without removing the driveshaft is almost impossible. On the other hand, four-wheel-drives are typically optimized for off-road usage. A full-time four-wheel-drive system will work similarly to all-wheel-drive, as it enables drivers to keep the wheels engaged. A part-time four-wheel-drive can let drivers disengage all four wheels at lower speeds manually. Most four-wheel-drives also have front and rear differentials, they also have transfer cases that can engage the rear and/or front axles. Issues Involved When Towing All-Wheel-Drives When towing a vehicle on two wheels, the common practice is not to tow the drive wheels. Towing the vehicle by drive wheels will result in damage to the transmission, even when the vehicle is left in neutral. Towing front-wheel-drive vehicles (FWD) will involve moving the car with the rear pair of wheels put onto the ground. On the other hand, towing rear-wheel-drive (RWD) means towing the vehicle with the front pair of wheels on the ground, the steering must be locked for safety purpose. The driveshaft of the rear-wheel-drive should also be removed if the rear wheels on the ground. For an all-wheel-drive vehicle, no wheels should be left on the ground; this is because the wheels are permanently engaged. If towing is done with a pair of wheels on the road, it can lead to damage to the transmission, the coupling, and other components of the vehicle. How to Tow All-Wheel-Drives Safely When towing all-wheel-drive vehicles, the safest way is to keep the wheels off the road. This is possible using a flatbed tow truck. Flatbed towing the all-wheel-drive is the most secure and efficient option of moving these vehicles without causing significant damage to the drivetrain. If flatbed tow trucks are not available, towing companies will substitute the towing using tow dollies to perform the duty. When flatbed tow trucks or trailers aren’t available, many tow truck and crane services resort to tow dollies to transport AWD vehicles while keeping their wheels above ground. Tow dollies have of inline pair of small wheels attached to a metal frame. The frame is put against the tires, and the two pairs of wheels linked with a set of aluminum axles. The wheels are put onto the tow dollies. The tow dollies cradle the wheels between the axles and keep them off from the ground. By using flatbed towing or tow dollies, the all-wheel-drives can be transported safely, as they can minimize the risks of damage to the drivetrain of the vehicle. Conclusion Thus, when towing vehicles, precautions should be taken before to prevent damages. There are different towing methods, so the towing company needs to determine the most appropriate option for the towing requests. All-wheel-drives do need more care, but they can be moved with the right tow truck and equipment. For 24-Hour Towing Services & Roadside Assistance in Los Angeles, Please Call Green Towing Los Angeles